MLAB




kategorie None

Status
ACOMP01A

ACOMP01A

Comparator with short responce time in order of nanoseconds. Didital output is on LVPECL/LVDS logic. Analog input is equiped by SMA connector.

AD1881A01A

AD1881A01A

Module is audio in and audio out interface for development board NGW100 with processor ATMEL AVR32. It uses common codec AD1881A.

ADCaudio01A

ADCaudio01A

Replaced module of ADCaudio01B.

ADCaudio01B

ADCaudio01B

Module has audio input interface. Digitalized audio data stream (I2S) with parametrers 192kHz@24bit.

ADCmonoPPI01A

ADCmonoPPI01A

Mono high speed analog to digital converter. With parallel data output.

ADCmonoSPI01A

ADCmonoSPI01A

Mono high resolution analog to digital converter. With serial data output.

ADCmonoSPI01B

ADCmonoSPI01B

Mono high resolution (16bit) analog to digital converter. With serial data output.

ALBASE0401

ALBASE0401

This base board has size 4x1 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions.

ALBASE1115

ALBASE1115

This base board has size 11x15 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions.

ALBASE1209

ALBASE1209

This base board has size 12x9 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions.

ALBASE1241

ALBASE1241

This base board has size 12x41 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions.

ALBASE1521

ALBASE1521

ALBASE1521

ALBASE2537

ALBASE2537

This base board has size 25x37 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions.

ALTIMET01A

ALTIMET01A

Breakout board for MPL115A1 or MPL115A2 integrated sensor chips. The sendor is capable to measure absolute pressure and temperature. It can be connectod to I2C bus.

ANT01A

ANT01A

Module contain a ANT transceiver and SMA antenna conector. Module has serial interface for direct connection to microcontroller.

AT32TQ14401A

AT32TQ14401A

Module is intended for development of applications based on powerful 32bit Atmel microcontrolers with AVR32 core AT32UC3A series.

ATXPOWER01A

ATXPOWER01A

Integrate ATX power standards to MLAB modules.

ATmega801A

ATmega801A

Processor module for ATMEL ATmega8 in TQFP32 package. The module contains processor and standard crystal or clock crystal can be used. There is RESET push button and ATMEL ISP 6 PIN connector.

ATmega801B

ATmega801B

Processor module for ATMEL ATmega8 in TQFP32 package. The module contains processor and standard crystal or clock crystal can be used. There is RESET push button and ATMEL ISP 6 PIN connector.

ATmega8DIL01A

ATmega8DIL01A

Processor module for ATMEL ATmega8 in DIL28 package. The module contains processor and standard crystal or clock crystal can be used. There is RESET push button and ATMEL ISP 6 PIN connector.

ATmegaTQ10001A

ATmegaTQ10001A

Processor module for ATMEL ATmega in TQFP100 package. The module can use standard and/or clock crystals. It is equipped with RESET push button and programming connector for ISP (6PIN) and JTAG (10PIN) programming.

ATmegaTQ4401A

ATmegaTQ4401A

Processor module for ATMEL ATmega in TQFP44 package. The module can use standard and/or clock crystals. It is equipped with RESET push button and programming connector for ISP (6 PIN) and JTAG (10 PIN) programming.

ATmegaTQ6401A

ATmegaTQ6401A

Processor module for ATMEL ATmega in TQFP64 package. The module can use standard and/or clock crystals. It is equipped with RESET push button and programming connector for ISP (6PIN) and JTAG (10PIN) programming.

ATprogISPUSB01A

ATprogISPUSB01A

The module allows ISP programming of AVR uControllers.

ATprogISPUSB02A

ATprogISPUSB02A

The USB programmer allows ISP programming of Atmel AVR uControllers. It can provide target 3.3V or 5V power from USB.

ATtinySO801A

ATtinySO801A

Old design. The processor module for TAMEL ATtiny in SO8 package consists of processor, headers, programming header and RESET push button.

ATtinySO801B

ATtinySO801B

The processor module for TAMEL ATtiny in SO8 package consists of processor, headers, programming header and RESET push button.

AVRUSB01A

AVRUSB01A

Processor module for AVR software version of (Low Speed) USB. May be used as ISP AVR programmer (with USBasp firmware), or USB to I2C convertor (with i2c-tiny-usb firmware). Uses ATmega88 in TQFP32 package.

BASE162101A

BASE162101A

MLAB base for modules constructions.

BASEBOX01A

BASEBOX01A

The printed plastic parts are sandwiched between standard hole-grid plates which makes the enclosure very rigid. The box sides can be easily customized for individual project needs, or separately exchanged during an instrument development.

BASEBOX02A

BASEBOX02A

The printed plastic parts are sandwiched between standard hole-grid plates which makes the enclosure very rigid. The box sides can be easily customized for individual project needs, or separately exchanged during an instrument development.

BASEBOX03A

BASEBOX03A

The printed plastic parts are sandwiched between standard hole-grid plates which makes the enclosure very rigid. The box sides can be easily customized for individual project needs, or separately exchanged during an instrument development.

BATPOWER01A

BATPOWER01A

Switched power unit.

BATPOWER02A

BATPOWER02A

Switched power unit.

BATPOWER03A

BATPOWER03A

Switched power unit with adjustable regulator.

BATPOWER04A

BATPOWER04A

Replaced module of BATPOWER04C

BATPOWER04B

BATPOWER04B

Replaced module of BATPOWER04C.

BATPOWER04C

BATPOWER04C

Converter module uses LM3485. Acceptable input voltage range is 4.5 V - 16V. Output voltage can be selected in fixed values 3,3 V 5 V or adjusted by trimmer. This module is especially suited for battery powered applications.

BLE01A

BLE01A

This module can add wireless comunication capability to your project via Bluetooth Low Energy protocol. This module uses NRF8001 chip, wich comunicates with the host controler via SPI the interface.

BP01A

BP01A

SMD construction of band pass filter intented to be used in radioastronomy applications. Primarily designed to 20-40MHz pass band.

BP01B

BP01B

SMD construction of band pass filter intented to be used in radioastronomy applications. Primarily designed to 20-40MHz pass band.

BRIDGEADC01A

BRIDGEADC01A

The module is a complete analog front end for weigh-scale and pressure measurement applications. The device accepts low-level signals directly from a bridge transducer and outputs a serialdigital word on SPI interface.Exitation voltage could be generated by module itself. Exitation signal is synchronous with internal signal sampling.

C01A

C01A

C01A

CLK1PLL01A

CLK1PLL01A

PLL clock generator with Texas Instruments chip CDCE913. Contains VCXO with external xtal andone internal PLL. It has three LVCMOS outputs with individual frequency dividers capable togenerate ut to 230MHz clocks. The chip is programmable via I2C and configuration may be savedto internal EEPROM.

CLKDIV01A

CLKDIV01A

Multiple division ratios can be selected by jumpers. Possible division ratios are: (÷1, ÷2, ÷4, ÷8) or (÷2, ÷4, ÷8, ÷16) every output is synchronous each other. The common enable (EN) is synchronous so that the internal dividers will only be enabled/disabled when the internal clock is already in the LOW state.

CLKGEN01A

CLKGEN01A

Single output I2C programmable clock generator.

CLKGEN01B

CLKGEN01B

Single output I2C programmable clock generator.

CLKGEN02A

CLKGEN02A

The module comprises a plurality of housings for mounting a variety of crystal oscillators.

CLKHUB02A

CLKHUB02A

high speed clock distributor with ten LVPECL outputs. Usable up to 3.5GHz

DIG4SW01A

DIG4SW01A

Switch for voltage from 3.4 V to 40 V. Resistance in spliced state 160 mOhm. Integrated circuit TPS4H160.

DIG4SWHI01A

DIG4SWHI01A

Switch for voltage from 4 V to 28 V. Resistance in spliced state 50 mOhm. Integrated circuit VNQ7050AJ.

DIP8SW01B

DIP8SW01B

DIP8SW01B

DRV8835HB01A

DRV8835HB01A

H-bridge-based ICs DRV8835HB. Allows you to control two DC motors in the range voltage 2V to 11V and maximum current of 1.5 A on the engine, or parallel, where it is then possible to control the 3A engine. Or the module can be used to control a stepper motor.

DRV8835HB01B

DRV8835HB01B

H-bridge-based ICs DRV8835HB. Allows you to control two DC motors in the range voltage 2V to 11V and maximum current of 1.5 A on the engine, or parallel, where it is then possible to control the 3A engine. Or the module can be used to control a stepper motor.

EEPROM01A

EEPROM01A

Contains some most popular serial eeproms.

EEPROM02A

EEPROM02A

Universal EEPROM module for communicating via the I2C interface in package types: SO8, TSSOP8, MSOP8.

ETH01A

ETH01A

MII standard interface ethernet module with full PoE compatibility.

ETH02A

ETH02A

RJ-45 socket with impedation matching useful for connecting ethernet compatible controllers to ethernet standard network.

FMC2DIFF01A

FMC2DIFF01A

This module converts VITA 57 FMC-LPC connector to SATA or miniSAS connectors.

FT230X01A

FT230X01A

The module allow conecting RS232 CMOS/TTL device to USB. Uses FTDI chip FT230XS. The chip is supported in all contemporary systems.

GB01A

GB01A

Provide FR wideband gain dependend on type of MMIC populated on the board.

GP201A

GP201A

Measure time intervals up to 4us with precision 65ps. Also is capable for measure temperature (with 16bit resolution) if module is connected to temperature sensor such as PT1000.

GPS01A

GPS01A

The module is capable of receiving GPS signals. Communications interfaces I2C, USB, serial line.

GPS01B

GPS01B

The module is capable of receiving GPS signals. Communications interfaces I2C, USB, serial line.

GSENSE01A

GSENSE01A

Triple axis accelerometer with proportional analog output.

GSM01A

GSM01A

Replaced GSM01B

GSM01B

GSM01B

Provide wideband GSM and 3G data connectivity services available in standard cellular phone networks.

HB1FET01A

HB1FET01A

Power bridge for 50V and 80A.

HB2FET01A

HB2FET01A

Malfunction construction.

HBRIDGE03A

HBRIDGE03A

Full bridge 6-45 V max 3.6A for DC motors. It uses circuit DRV8871.

HBSTEP01A

HBSTEP01A

HBSTEP01A

HBSTEP01B

HBSTEP01B

Stepper motor driver

HBSTEP02A

HBSTEP02A

Stepper motor driver

HUM01A

HUM01A

Humidity sensor based on HIH-5030/5031 chip. Analog output is ratiometric.

I2C232V01A

I2C232V01A

The base module is an integrated circuit SC18IM700, who works as a converter I2C / UART. I2C interface acts as the master. I2C can be used to speed 400kbit / Sau UART can be up to 460.8 kbit / s.

I2CADC01A

I2CADC01A

24-bit converter, which is controlled via the I2C interface. It includes a temperature sensor that can be used to compensate. Therefore, this module is also suitable for use with thermocouples, because it can provide cold junction compensation.

I2CDIFF01A

I2CDIFF01A

Allows long range I²C communication in harsh environment.

I2CDIFF01B

I2CDIFF01B

Allows long range I²C communication in harsh environment. Beside I²C allows bidirection interrupt transmission over the same link.

I2CHUB01A

I2CHUB01A

The module allow conecting multiple I2C devices together. It does not consist any configurable IO. It is a simple bus multiplyer.

I2CHUB01B

I2CHUB01B

The module allow conecting multiple I2C devices together. It does not consist any configurable IO. It is a simple bus multiplyer.

I2CHUB02A

I2CHUB02A

Replaced I2CHUB02B

I2CIO01A

I2CIO01A

This GPIO expander module is designed for 1.65 to 5.5 V operation. It provides general-purpose remote I/O expansion via the I²C interface.The module consists of two 8-bit Configurable, Input Port, Output Port, and Polarity Inversion registers.

I2CPWM01A

I2CPWM01A

The module allows the generation of PWM signal, which can be adjusted using the I2C interface. The module has eight outputs that can run simultaneously on two frequencies in the range of 0.59 Hz - 152 Hz (with 1.69 - 6.58 ms).

I2CSPI01A

I2CSPI01A

Allows connection of SPI devices to I2C bus. The module is capable co handle up to four SPI slaves. Not used chip-select pins can be used as GPIO pins.

IMU01A

IMU01A

The module can be fitted with circuit MMA8451Q. It is a 3-axis accelerometer with 14-bit resolution. A3G4250D circuit provides the 3-axis gyroscope. Both circuits enable communication via I2C. On the module is not necessary to assemble both IO.

INPUTUNI01A

INPUTUNI01A

Construction of universal high voltage protected / galvanic isolated input. Can be used both for analog and digital signals.

IRDA01A

IRDA01A

None

IRFEE01A

IRFEE01A

The sensor uses modulated infrared signal for distant detection of obstacles. It mmaybe seen as virtual feeler for roboot. The sensor uses processor ATtiny and infraredsensor for remote control. The modulation and statistical processing of the signalgives the sensor good noise imunity.

ISL02A

ISL02A

Light sensor with I2C interface and UV index measuring capability.

ISL03A

ISL03A

Light sensor with I2C interface to 168 klx.

ISL2902001A

ISL2902001A

Light sensor ISL29020 with I2C interface. Measurement range 0.015lux - 64.000lux.

IUC01A

IUC01A

This sensor measures electric current with high precision over wide range of currents up to 30A and 80kHz bandwith. This sensor has a linear voltage output.

JTAGFT2232V01A

JTAGFT2232V01A

The module allow J-TAG programming via USB.

JTAGFT2232V02A

JTAGFT2232V02A

The module allow J-TAG programming via USB.

LCD2L4P01A

LCD2L4P01A

Module with two-line LCD display with Hitachi controller and with 4 push buttons. It can be used as human interface for small projects with microcontrollers.

LCD2L4P02A

LCD2L4P02A

Module with two-line LCD display (with Hitachi controller), with 4 push buttons and with piezoelement powered by 74HC04.

LCDHOLDER2X16V01A

LCDHOLDER2X16V01A

The hodlder can be prited at almost any 3D printer.

LCDholder

LCDholder

The hodlder can be prited at almost any 3D printer.

LDD01A

LDD01A

Three-channel laser diode pulse regulator module enables the continuous wave operation of laser diodesor spike-free switching with defined current pulsesin a frequency range of up to 155 MHz. The threechannels can be accumulatively pulsed and the peak optical power ofthe laser diode is regulated separately.

LED01A

LED01A

LED01A

LED7SEG01A

LED7SEG01A

LED 7-segmentový display ovládaný přes I2C

LEDROBOT

LEDROBOT

This module contain switch, LEDs, voltage regulator, beeper and 5V power hub.

LEDbar01A

LEDbar01A

There are 8 LEDs drived by simple shift register. Construction is useful to indicate status on small robots.

LEDbar02A

LEDbar02A

There are 8 LEDs drived by simple shift register. Construction is useful to indicate status on small robots. SMD version

LINREG01A

LINREG01A

The module can be fitted in housings linear stabilizers D2PAK (TO263), SOT223, DPAK (252).

LION1CELL01A

LION1CELL01A

Replaced module of LION1CELL01B.

LION1CELL01B

LION1CELL01B

Integrated battery management solution for 18650 li-ion batteries. It can measure remaining energy in battery, perform charging cycle from external power source and protect batteries against over voltage or over draining conditions.

LION2CELL01B

LION2CELL01B

Replaced by LION2CELL01D

LION2CELL01C

LION2CELL01C

Integrated battery management solution for 18650 li-ion batteries. It can measure remaining energy in battery, perform charging cycle from external power source and protect batteries against over voltage or over draining conditions.

LION2CELL01D

LION2CELL01D

Integrated battery management solution for 18650 li-ion batteries. It can measure remaining energy in battery, perform charging cycle from external power source and protect batteries against over voltage or over draining conditions.

LM108601A

LM108601A

Small voltage stabilizer. Based on LM1086.

LM38601A

LM38601A

Module of small universal audio amplifier with LM386 can be used for receivers and other devices requiring low output power. The amplifier is equipped with jumpers for setting of parameters (gain and frequency) so that it can be used more universally.

LNA01A

LNA01A

Very low noise <0.8dB band pass amplifier to multi frequency bands.

LTS01A

LTS01A

Temperature sensor with I2C digital bus and absolute accuracy of 0.5 K.

MAG01A

MAG01A

Precision I2C magnetometer for compass and navigation applications in robotics.

MAX1797

MAX1797

Switched power unit up to 5V and 1A.

MBA81001A

MBA81001A

Module of 5W audio amplifier with MBA810 (TBA810). The chip is old and it was used because we had lots of them.

MC3406301A

MC3406301A

Switched power unit with adjustable regulator.

MPC17511HB01A

MPC17511HB01A

The module uses two Freescale H-Bridges MC17511A. Power supply is 2.0-6.8V, current 1A, max 3A (per bridge). It is intended for driving small motors.

MPC17529HB01A

MPC17529HB01A

The module uses dual H-Bridge made by Freescale MC17529.The power voltage is 2.0-6.8V, the current 2x0.7A, maximum current max 2x1.4A. It is intended for small motors.

NFET2X01A

NFET2X01A

There are 2 NFETs switching to earth. Inductive load is allowed.

NFET2x2

NFET2x2

There are 4 NFETs switching to earth. Inductive load is allowed.

NFET4X01A

NFET4X01A

There are 4 NFETs switching to earth. Inductive load is allowed.

NFET4X01B

NFET4X01B

There are 4 NFETs switching to GND. Parameters depending on type of soldered FETs. Inductive load is allowed.

ODROID-C1

ODROID-C1

Computer module for applications which needs full Linux operating system and lot of computing power. It is suitable for machine control or home automation as example.

ODROID-C2

ODROID-C2

Computer module for applications which needs full Linux operating system and lot of computing power. It is suitable for machine control or home automation as example.

ODROID-U3

ODROID-U3

Computer module for applications which needs full Linux operating system and lot of computing power. It is suitable for machine control or home automation as example.

ODROID-XU4

ODROID-XU4

Computer module for applications which needs full Linux operating system and lot of computing power. It is suitable for machine control or home automation as example.

ODroid-X2

ODroid-X2

Computer module for control applications in which computing power is desired. 1.7GHz Quad core ARM Cortex-A9 MPCore, 2GB Memory, Linux operating system.

OZDUAL02A

OZDUAL02A

Construction of the module is developed as universal circuit module for dual operational amplifier in SO8 package. Module contains voltage reference. This module can be used for all standard operational amplifier applications. Circuitry is modified by populating the module by SMD resistors.

OZDUAL02B

OZDUAL02B

Construction of the module is developed as universal circuit module for dual operational amplifier in SO8 package. Module contains voltage reference. This module can be used for all standard operational amplifier applications. Circuitry is modified by populating the module by SMD resistors. This is new redesign with more friendly components placement.

OZdual01A

OZdual01A

Construction of the module is optimized for most dual operational apmlifier in DIL8 package. Contains voltage reference.

OZpower01A

OZpower01A

Construction of single power operational aplifier suitable for 18V/3A

OZquad01A

OZquad01A

Construction of the module is optimized for most quad operational apmlifier in DIL14 package.

OZquad01B

OZquad01B

Construction of the module is optimized for most quad operational apmlifier in DIL14 package.

PIC16F87xTQ4401A

PIC16F87xTQ4401A

The processor module for MICROCHIP PIC16F87x in TQFP44 package consists of processor, headers, programming header and RESET push button.

PIC16F87xTQ4401B

PIC16F87xTQ4401B

The processor module for MICROCHIP PIC16F87x in TQFP44 package consists of processor, headers, programming header and RESET push button.

PIC18F4550v01A

PIC18F4550v01A

The processor module for MICROCHIP PIC18F4550 in TQFP44 package consists of processor, headers, programming header, USB interface and RESET push button.

PIC18F8xTQ8001A

PIC18F8xTQ8001A

Module for work with PIC18F MCU in TQFP80 package. On PCB is a bias resistor for Ethernet peripheral.

PICPGR301A

PICPGR301A

The programmer uses LPT port of PC and contains 5V voltage regulator so it can be used for powering target application. The programmer has tree state outputs and that is why it is not necessary to disconnect it from target application while debugging.

PICPROGUSB02A

PICPROGUSB02A

The programmer is compatible with PicKit 2 design of Microchip. The programmer uses USB port. The programmer has tree state outputs and that is why it is not necessary to disconnect it from target application while debugging. A special feature of this programes is logic analyzer.

PIND01A

PIND01A

The module includes a parallel-connected diodes for PINS dosimeter.

PLBASE1115

PLBASE1115

This base board has size 11x15 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions. The board can be prited at almost any 3D printer.

PLBASE1515

PLBASE1515

This base board has size 11x15 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions. The board can be prited at almost any 3D printer.

PLCASE1115

PLCASE1115

Basic printable case for the base board with size 11x15 holes.

PWMLED01A

PWMLED01A

Replaced by PWMLED01C.

PWMLED01B

PWMLED01B

Replaced by PWMLED01C.

PWMLED01C

PWMLED01C

This module is usefull for PWM dimming of power LEDs.

R01A

R01A

R01A

RAINGUAGE01A

RAINGUAGE01A

RAINGUAGE01A module

REL1SW01A

REL1SW01A

Universal module for relays. The module is equipped with two NMOSFETy that are designed for relay processor. Wiring module allows you to use two transistors alone without the relay as a switch to GND.

REL8SW01A

REL8SW01A

There are 8 switching relays. Digitaly controlled by ULN2803

RFMIX01A

RFMIX01A

Low power RF mixer with differential input and output.

RFdetect01A

RFdetect01A

The wide bandwitch logarithmic amplifier and detector suitable for radio frequency measurement.

RGBC01A

RGBC01A

The sensor comprises a sensor red, green, blue and clear colors. Communication takes place via the I2C interface. Circuit includes a power supply for external IR LED. The sensor can be used to measure lighting conditions, or also for detection of the line for the bar and the robot for sensing rotation of automotive wheels.

RGBHD01A

RGBHD01A

RGB Head consists of 3 pairs of Read, Green and Blue LEDs and of one fototransistor.

RJ12V01A

RJ12V01A

Module with RJ12 connector, which is used primarily for connecting sensors.

RJ45V01A

RJ45V01A

Designed primarily to connect to the I2C DIFF as an extension of another RJ45 connectors.

RPS01A

RPS01A

In is a contactless magnetic position sensor for accurate angular measurement over a full turn of 360 degrees. To measure the angle, only a simple two-pole magnet, rotating over the center of the chip, is required. The absolute angle measurement provides instant indication of the magnet’s angular position with a resolution of 0.0879º. This digital data is available as a serial bit stream.

RPi

RPi

Documents and design files describing a mothod how to use classic Raspberries Pi in MLAB prototyping system.

RPi3

RPi3

Documents and design files describing a mothod how to use classic Raspberry Pi 3 in MLAB prototyping system.

RS232SINGLE01A

RS232SINGLE01A

The module uses well known MAX232 chip and is intended as a level converter. It uses RX/TX signals and a pair of flow control signals (selectable by jumpers). Original RS232 signals are available on header pins.

RTC01A

RTC01A

Replaced RTC02A

RTC02A

RTC02A

Real Time Clock controlled through I2C with battery backup. The accuracy of the order of 20 ppm.

RX433MHz01A

RX433MHz01A

Receiver useful for low speed telemetry transmision.

S3AN01A

S3AN01A

Replaced by an updated version S3AN01B. <br> The school board allows interested people to play with FPGA from XILINX. The board contains LED display, some switches and push buttons. It has VGA video port, PS/2 ports for keyboard and mouse. Because the main chip is not 5V tolerant, the board is equipped with 5V tolerant buffers (inputs). The board is powered from 5V, internal power supply is included. For timing there is one 100MHz crystal oscillator.

S3AN01B

S3AN01B

The school board allows interested people to play with FPGA from XILINX. The board contains LED display, some switches and push buttons. It has VGA video port, PS/2 ports for keyboard and mouse. Because the main chip is not 5V tolerant, the board is equipped with 5V tolerant buffers (inputs). The board is powered from 5V, internal power supply is included. For timing there is one 100MHz crystal oscillator.

S6AN01A

S6AN01A

FPGA development module for basic signal and data processing. This breakout board differs from other constructions by high number of differential pairs take out to LVDS or LVPECL connectors.

SDRX01A

SDRX01A

None

SDcard01A

SDcard01A

Simple SD card terminal with voltage regulator.

SDcard01B

SDcard01B

Simple SD card terminal with voltage regulator. And simple overvoltage protection on inputs.

SERVOHUB01A

SERVOHUB01A

Hub interface for powering and driving standard RC servos from an MCU.

SHT25V01A

SHT25V01A

SHT25 sensor module which measures relative humidity from 0% to 100% with an accuracy of + / - 1.8%. Temperature is measured in the range -40 ° C to 125 ° C with a an accuracy of 0.2 ° C.

SHT31V01A

SHT31V01A

SHT31 sensor module which measures relative humidity from 0% to 100% with an accuracy of + / - 2%. Temperature is measured in the range -40 ° C to 125 ° C with a an accuracy of 0.3 ° C.

SMA2SATA01A

SMA2SATA01A

Converter from asymetric coaxial cable with SMA connector to cables with SATA connectors. Converter is based on Ethernet signal transformer. Construction of converter is bidirectional and allows balance to unbalance connections (balun).

SOLAR01A

SOLAR01A

Module permanently search maximum power point of connected photovoltaic panel and convert the generated energy to higher voltages (40V maximum). This allow serial or parralel connection of non strictly uniform pannels. It can be used for fotovoltaic panels in range of tend or hundreds of Watts.

SOLARMINI01A

SOLARMINI01A

Module permanently search maximum power point of connected photovoltaic panel and convert the generated energy to higher voltages (5V maximum). It can be used for single cell or few serial connected cells.

SPIDIFF01A

SPIDIFF01A

Allows middle range SPI communication in harsh environment.

STM32F10xRxT01A

STM32F10xRxT01A

STM32 10X series dovelopment module.

SUPERCAP01A

SUPERCAP01A

The module is suitable for covering power outages devices. By detecting the input voltage drop can be used for early shutdown of computers type ODROID on power.

SUPERCAP01B

SUPERCAP01B

The module is suitable for covering power outages devices. By detecting the input voltage drop can be used for early shutdown of computers type ODROID on power.

SW01A

SW01A

SW01A

SYMPOWER02A

SYMPOWER02A

Symmetric power supply ranging from 1.5 V - 5 V, 250 mA.. It uses circuit LM27762.

THERMOGEN01A

THERMOGEN01A

Thermoelectric generator power supply designed to use in low power typically wireless devices which should work for longtime without batteries.

THERMOPHILE01A

THERMOPHILE01A

Contact less IR temperature sensor with SMBus interface.

TL01A

TL01A

TL01A

TOUCHBOARD01A

TOUCHBOARD01A

Capacitive touch board with I²C interface.

TPS61170

TPS61170

Switched adjustable DC/DC power unit.

TPS61200

TPS61200

Switched adjustable power unit step-down and step-up in one module.

TPS63000

TPS63000

High efficiency switched adjustable power unit step-down and step-up in one module.

TPS63060V01A

TPS63060V01A

The drive uses the TPS63060 circuit. The input voltage range of 2.5 V - 12V. The output voltage of 3.3 V, 5 V.

TRIACSHARP02A

TRIACSHARP02A

There are 8 solid state switching relays which can be digitally controlled by open collector. It can operate up to 8A on 250VAC.

TRIM01A

TRIM01A

TRIM01A

TRIMQUAD01A

TRIMQUAD01A

There are four trimmers conected parallely to supply voltage. Allow generetion analog signals to setup system behavivour.

TTLCAN01A

TTLCAN01A

The module allow conecting uprocessors to CAN bus

TTLCAN01B

TTLCAN01B

The module allow conecting uprocessors to CAN bus

TTLPECL01A

TTLPECL01A

Translate between TTL a differential PECL logic levels direction of translation can be chosen by type of mounted chip.

TTLRS48501A

TTLRS48501A

The module allow conecting uprocesors to RS485 bus

TXIR01A

TXIR01A

The module is useful for quick implementation SPI IR transmitter

TXIR01B

TXIR01B

The module is useful for quick implementation SPI IR transmitter

TXsaw433MHz01A

TXsaw433MHz01A

Transceiver useful for low speed telemetry transmision.

Text_Examples

Text_Examples

Simple Example programs to start with.

UNIATMEGA8TQFP01A

UNIATMEGA8TQFP01A

Single sided PCB proto-board for ATMEGA8 in TQFP32 or compatible, with TL317 regulator position, free SOIP/SO/SOIC-8, -14, -16, -20 and MSOP-8 positions. Matrix for both through-hole and SMD prototyping included.IMPORTANT: ISP ground has to be wired!

UNIBOX01A

UNIBOX01A

Universal metal module housing box with interchangeable front and back panels. Useful for housing construction of devices created from MLAB modules.

UNIBOX03A

UNIBOX03A

Universal metal module housing box with interchangeable front and back panels. Useful for housing construction of devices created from MLAB modules. With a pair of sidewalls printable 3D printer. Dimensions 220x160x51.5 mm.

UNIPOWER02A

UNIPOWER02A

Universal power supply module 5V or 12V.

UNIPOWER03A

UNIPOWER03A

Universal power supply module 5V or 12V.

UNIPOWER04A

UNIPOWER04A

Universal 10x 1A power supply module 5V or 12V.

UNIPOWER05A

UNIPOWER05A

Universal 10x 1A power supply module 5V or 12V.

UNIPOWER06A

UNIPOWER06A

Universal 10x 1A power supply module 5V or 12V.

UNIPOWER07A

UNIPOWER07A

Universal 10x 1A power supply module 5V or 12V.

UNISERIAL01A

UNISERIAL01A

Module is designed to connection of shielded multi wire cable to sensitive MLAB modules. The module contains over voltage protection. It can be used to connection of I2C, RS232, RS485 or CAN physical layers.

UNIUNI01A

UNIUNI01A

Platfolm for soldering testing circuits.

UNIUNI02A

UNIUNI02A

UNIUNI02A

UNIUNI03A

UNIUNI03A

UNIUNI03A

UPCONV01A

UPCONV01A

Voltage up-converting module for 5V, 12V power levels or user selectable voltage. Usually used for powering devices from single cell battery.

USB232R01A

USB232R01A

The module allow conecting RS232 TTL device to USB.

USB232R01B

USB232R01B

The module is universal converter from USB to RS232 with TTL/CMOS signal levels (both 3.3V and 5V). The converter uses FT232R chip from FTDI and is supported in all main operating systems.

USB4xUART01A

USB4xUART01A

USB to 4x RS232 (UART). It uses circuit FT4232HL.

USBHUB01A

USBHUB01A

Fourfold USB 3.0 HUB settings via I2C.

USBI2C01A

USBI2C01A

Convert interface I2C to USB standard, it acts as a HID device, so you do not need non-standard drivers. It also allows participation in the I2C system bus.

USBI2S01A

USBI2S01A

USB to I2S converter for interfacin I2S audio devices to standard USB port. It is compatible with UAC standard.

USBIO01A

USBIO01A

A high speed USB2.0 IO communication module. It si suitable for fast parallel transfers. It is based on CY7C68013A USB chip.

VCAI2C01A

VCAI2C01A

4-channel 18-bit AD converter voltage and current for industrial sensors. Ranges: 0-5V, 0-10V, 0-20mA, 4-20mA, 0-40 mA.

VLT01A

VLT01A

Convert digital signals between two voltage levels.

XVC_FT220X01A

XVC_FT220X01A

XVC JTAG programming cable for downloading and debug projects with XILINX FPGA/CPLD device. It is directly supported by ISE design software (and Chipscope as well). The design software sends commands across network to the computer with this cable attached to it and supporting software sends data to JTAG interface. This XVC cable is based on a cheap FTDI FT220X chip.

XVC_FT220X02A

XVC_FT220X02A

XVC JTAG programming cable for downloading and debug projects with XILINX FPGA/CPLD device. It is directly supported by ISE design software (and Chipscope as well). The design software sends commands across network to the computer with this cable attached to it and supporting software sends data to JTAG interface. This XVC cable is based on a cheap FTDI FT220X chip.

nanoterm01A

nanoterm01A

Displays simple text messages and allow interaction with system via some buttons.

nanoterm02A

nanoterm02A

Displays simple text messages and allow interaction with system via some buttons.

Zobrazeno 278 položek.