MLAB




kategorie commserial

Status
TTLCAN01A

TTLCAN01A

The module allow conecting uprocessors to CAN bus

I2CIO01A

I2CIO01A

This GPIO expander module is designed for 1.65 to 5.5 V operation. It provides general-purpose remote I/O expansion via the I²C interface.The module consists of two 8-bit Configurable, Input Port, Output Port, and Polarity Inversion registers.

I2CHUB01A

I2CHUB01A

The module allow conecting multiple I2C devices together. It does not consist any configurable IO. It is a simple bus multiplyer.

I2CHUB02A

I2CHUB02A

Replaced I2CHUB02B

USB232R01A

USB232R01A

The module allow conecting RS232 TTL device to USB.

USB232R01B

USB232R01B

The module is universal converter from USB to RS232 with TTL/CMOS signal levels (both 3.3V and 5V). The converter uses FT232R chip from FTDI and is supported in all main operating systems.

I2C232V01A

I2C232V01A

The base module is an integrated circuit SC18IM700, who works as a converter I2C / UART. I2C interface acts as the master. I2C can be used to speed 400kbit / Sau UART can be up to 460.8 kbit / s.

I2CPWM01A

I2CPWM01A

The module allows the generation of PWM signal, which can be adjusted using the I2C interface. The module has eight outputs that can run simultaneously on two frequencies in the range of 0.59 Hz - 152 Hz (with 1.69 - 6.58 ms).

USBHUB01A

USBHUB01A

Fourfold USB 3.0 HUB settings via I2C.

USB4xUART01A

USB4xUART01A

USB to 4x RS232 (UART). It uses circuit FT4232HL.

ETH02A

ETH02A

RJ-45 socket with impedation matching useful for connecting ethernet compatible controllers to ethernet standard network.

TTLCAN01B

TTLCAN01B

The module allow conecting uprocessors to CAN bus

TTLRS48501A

TTLRS48501A

The module allow conecting uprocesors to RS485 bus

FT230X01A

FT230X01A

The module allow conecting RS232 CMOS/TTL device to USB. Uses FTDI chip FT230XS. The chip is supported in all contemporary systems.

USBIO01A

USBIO01A

A high speed USB2.0 IO communication module. It si suitable for fast parallel transfers. It is based on CY7C68013A USB chip.

JTAGFT2232V02A

JTAGFT2232V02A

The module allow J-TAG programming via USB.

I2CHUB01B

I2CHUB01B

The module allow conecting multiple I2C devices together. It does not consist any configurable IO. It is a simple bus multiplyer.

JTAGFT2232V01A

JTAGFT2232V01A

The module allow J-TAG programming via USB.

RS232SINGLE01A

RS232SINGLE01A

The module uses well known MAX232 chip and is intended as a level converter. It uses RX/TX signals and a pair of flow control signals (selectable by jumpers). Original RS232 signals are available on header pins.

USBI2S01A

USBI2S01A

USB to I2S converter for interfacin I2S audio devices to standard USB port. It is compatible with UAC standard.

SERVOHUB01A

SERVOHUB01A

Hub interface for powering and driving standard RC servos from an MCU.

ETH01A

ETH01A

MII standard interface ethernet module with full PoE compatibility.

I2CSPI01A

I2CSPI01A

Allows connection of SPI devices to I2C bus. The module is capable co handle up to four SPI slaves. Not used chip-select pins can be used as GPIO pins.

USBI2C01A

USBI2C01A

Convert interface I2C to USB standard, it acts as a HID device, so you do not need non-standard drivers. It also allows participation in the I2C system bus.

Zobrazeno 26 položek.