Differential pressure wind speed sensor with magnetometer.
High-performance wireless transceiver, ideal for remote control, data links, and sensor networks.
Mechanical parallella peripheral board
QFH active antenna analog front end and down converter
UTP cable RF signal I/Q interface for QFHMIX module
The module featuring two RF switches. Designed for radio transceivers with separate input and output.
ISM RF module with LoRa network capability
Direct conversion IQ output SDR receiver.
Dual-cell Li-Ion Battery management system.
Strain Gauges analog front end and ADC
Universal USB-UART converter ideal for prototyping high-quality devices. USB Full Speed/Full Handshake support.
28V input 1 MHz switching step-down converter
Symmetrical RF filter module with SATA connector input/output
RF balun with unballanced MCX/SMA and balanced SATA connectors
VLF antenna connection module
Singe cell Li-ion battery management module
The MLAB TPS63060V01A module is a versatile voltage converter based on the TPS63060 IC from Texas Instruments. It offers selectable output voltages (3.3V or 5V), flexible activation, power-saving mode, and can be synchronized with an external clock.
Small low-power MPPT module for photovoltaic cells.
Step-up converter. Vin 1,8 V - 5 V, Vout up to 28 V.
Small low-power photovoltaic MPPT module with LTO battery
Small low-power open-source toolchain compatible FPGA
The module is electro-mechanical interface between scintillation crystal and signal processing unit.
USB device to I²C master adapter with Linux kernel support
I2CHUB02 is low voltage I2C multiplexer (hub) which allows you to divide I2C bus into 8 separate buses, where the user can switch and connect individual sub-bus differently. This can connect multiple I2Cs to the device, change the voltage levels, or disconnect a certain part of the bus when it is stuck.
Allows connection of SPI devices to I2C bus and is capable co handle up to four SPI slaves. Not used chip-select pins can be used as GPIO pins.
High-effeciency (over 90%) stepdown converter based on LM3485 PFET Buck controller. Input vortage 4.5 V - 16V; Output voltage can be selected by jumper in fixed values of 3,3V, 5V or custom voltage by external resistor or trimmer.
Universal power supply module from barrel DC connector and WAGO terminals to MLAB modules. The module contains a resettable fuse, switch and LED indicator. Module can be used either for 5V and 12V.
LED01A is a simple MLAB module that contains 4 LED diodes. The module is useful for debugging and indicating individual states of systems built from MLAB construction kit
GPIO expander with I²C interface; 16-bit I/O, configurable ports, polarity inversion.
MLAB OLED display breakout. The module uses high-quality OLED display with high contrast and readability. It includes a level converter, reset circuit, LEDs, and a buzzer. Suitable for various electronics applications, where you need to show something.
voltage and current measuring ADC with I2C interface
I2C module for measuring 0-50A current and 0-50V voltage with high accuracy and reliability.
High-accuracy barometric pressure and temperature sensing module with MS561101BA03.
8 Mbit FRAM (CY15B108QN) fast data write, low power consumption, and high radiation resistance data storage
Buck-boost convertor TSP631000
Four-channel analog multiplexer with single-sided output
This 4-pin module connects JST-GH connectors, often used in Pixhawk drones, to standard pin headers, making it easier to build custom electronics and use I2C or CAN bus communication.
24-bit analog to digital converter with I2C interface
Board for mounting thick semiconductor diodes into existing devices.
Board for mounting thick semiconductor diodes into existing devices.
Board for mounting thick semiconductor diodes into existing devices.
This base board has size 4x1 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions.
This base board has size 11x15 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions.
This base board has size 12x08 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions.
This base board has size 12x09 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions.
This base board has size 12x41 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions.
Motherboard ALBASE1505 has 15x5 holes with a spacing of 10.16 mm. Its overall dimensions are adapted for insertion into the box UNIBOX03A.
MLAB base-board with size 15x21 holes with standard MLAB grid 400mils (10.16mm). The board on the sides contains a series of M3 holes with a metric pitch (10 mm) and three holes for stacking the boards above each other.
MLAB base-board with size 15x21 holes with standard MLAB grid 400mils (10.16mm)
This base board has size 16x08 holes and standard MLAB grid 400mils (10.16mm)
MLAB aluminium baseboard with 16x9 holes with a standard pitch of 400mils (10.16mm). Suitable for devices placed in the 1455N1601 box.
This base board has size 25x37 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions.
The sensor comprises a sensor red, green, blue and clear colors. Communication takes place via the I2C interface. Circuit includes a power supply for external IR LED. The sensor can be used to measure lighting conditions, or also for detection of the line for the bar and the robot for sensing rotation of automotive wheels.
The module contains the AS5048B integrated circuit, which allows the measurement of the magnetic field perpendicular to the surface of the integrated circuit. The module is suitable for measuring the angular position of a magnet and constructing tachometers. The communication interface is I2C.
High precission SHT3x hygrometer (humidity and temperature sensor) in form of MLAB module.
Translate between TTL a differential PECL logic levels direction of translation can be chosen by type of mounted chip.
The module can be fitted with circuit MMA8451Q. It is a 3-axis accelerometer with 14-bit resolution. A3G4250D circuit provides the 3-axis gyroscope. Both circuits enable communication via I2C. On the module is not necessary to assemble both IO.
Light sensor ISL29020 with I2C interface. Measurement range 0.015lux - 64.000lux.
This sensor measures electric current with high precision over wide range of currents up to 30A and 80kHz bandwith. This sensor has a linear voltage output.
Lightning sensor module based on AS3935 Franklin Lightning Sensor IO. Sensor can be connected via I2C or SPI bus.
The MLAB LTS01 is a highly precise digital thermometer module utilizing the MAX31725 IC. It offers I2C connectivity, multiple resolution options, and low power consumption. Designed for a temperature range of -55°C to +150°C, it's perfect for home automation, industrial control, medical devices, and HVAC systems.
Precision I2C magnetometer for compass and navigation applications in robotics.
Xilinx Spartan 3 XC3S50AN FPGA School Board
Module is intended for development of applications based on powerful 32bit Atmel microcontrolers with AVR32 core AT32UC3A series.
ATmegaTQ3201 module for ATMEL TQFP32 processors, includes RESET button and ATMEL ISP 6-pin connector, supports standard crystal or external clock.
Microcontroller ATmega in TQFP44 package. The module can use standard clock crystals. It is equipped with RESET push button and programming connector for ISP (6 PIN) and JTAG (10 PIN) programming.
Processor module for ATMEL ATmega in TQFP64 package. The module can use standard and/or clock crystals. It is equipped with RESET push button and programming connector for ISP (6PIN) and JTAG (10PIN) programming.
The ATprogISPUSB02A is an MLAB module enabling ISP programming of Atmel AVR microcontrollers. It offers USB power supply with 3.3V or 5V options and is compatible with STK500 programmers, allowing easy creation of Arduino-compatible ATmega modules.
The MCU module for MICROCHIP PIC18F4550 in TQFP44 package, programming header, USB interface and RESET push button.
The processor module for MICROCHIP PIC16F87x in TQFP44 package consists of processor, headers, programming header and RESET push button.
Module for work with PIC18F MCU in TQFP80 package. On PCB is a bias resistor for Ethernet peripheral.
Very low noise <0.8dB band pass amplifier to multi frequency bands.
SMD construction of band pass filter intented to be used in radioastronomy applications. Primarily designed to 20-40MHz pass band.
Module contain a ANT transceiver and SMA antenna conector. Module has serial interface for direct connection to microcontroller.
Measure time intervals up to 4us with precision 65ps. Also is capable for measure temperature (with 16bit resolution) if module is connected to temperature sensor such as PT1000.
Audio to digital converter ADCaudio01B Module has audio input interface. Digitalized audio data stream (I2S) with parametrers 192kHz@24bit.
Symmery transformer module e.g. balun for low frequency (audio) signals.
Single output I2C programmable clock generator.
Multiple division ratios can be selected by jumpers. Possible division ratios are: (÷1, ÷2, ÷4, ÷8) or (÷2, ÷4, ÷8, ÷16) every output is synchronous each other. The common enable (EN) is synchronous so that the internal dividers will only be enabled/disabled when the internal clock is already in the LOW state.
The module comprises a plurality of housings for mounting a variety of crystal oscillators.
Real Time Clock controlled through I2C with battery backup. The accuracy of the order of 20 ppm.
The module allows the generation of PWM signal, which can be adjusted using the I2C interface. The module has eight outputs that can run simultaneously on two frequencies in the range of 0.59 Hz - 152 Hz (with 1.69 - 6.58 ms).
The module allow conecting multiple I2C devices together. It does not consist any configurable IO. It is a simple bus multiplyer.
A high speed USB2.0 IO communication module. It si suitable for fast parallel transfers. It is based on CY7C68013A USB chip.
The base module is an integrated circuit SC18IM700, who works as a converter I2C / UART. I2C interface acts as the master. I2C can be used to speed 400kbit / Sau UART can be up to 460.8 kbit / s.
The TTLRS48501A is a versatile TTL to RS485 converter module with jumper-configurable terminator support for enhanced compatibility.
The module uses well known MAX232 chip and is intended as a level converter. It uses RX/TX signals and a pair of flow control signals (selectable by jumpers). Original RS232 signals are available on header pins.
LED 7 segment display with I2C interface. Module can be used for simple numerical data display.
Universal EEPROM breakout with I2C interface in package types: SO8, TSSOP8, MSOP8.
The module can be fitted in housings linear stabilizers D2PAK (TO263), SOT223, DPAK (252).
Symmetric charge pump power supply ranging from 1.5 V - 5 V, 250 mA.
Highly efficient buck-boost converter module (TPS63036V01) for stable power output in portable and low-power devices.
Switch for voltage from 4 V to 28 V, resistance 50 mOhm. Integrated circuit VNQ7050AJ.
Switch for voltage from 3.4 V to 40 V. Resistance in spliced state 160 mOhm. Integrated circuit TPS4H160.
Quad power MOSFET D-PAK transistors.
Dual MOSFET or single Relay switching module.
This module converts VITA 57 FMC-LPC connector to SATA or miniSAS connectors.
Designed primarily to connect to the I2C DIFF as an extension of another RJ45 connectors.
Module is designed to connection of shielded multi wire cable to MLAB modules.
Universal breadboard PCB for MLAB kit system
Sensorless driver of BLDC and PMSM motors based on DRV10987 controller.
USB power delivery solution for charging, or as a universal power source.
Multiple parallel Li-ion 18650 battery cell module with BMS and data storage with MCU control.
Sample and hold circuit for photomultiplier and semiconductor PIN diode pulse signal processing
Adapter for fast battery and data storage connection. Compatibile with BATDATUNIT01
MCU board with RP2040 dual-core microcontroller.
