MLAB



Modules
XVC_FT220X02A

XVC_FT220X02A

XVC JTAG programming cable for downloading and debug projects with XILINX FPGA/CPLD device. It is directly supported by ISE design software (and Chipscope as well). The design software sends commands across network to the computer with this cable attached to it and supporting software sends data to JTAG interface. This XVC cable is based on a cheap FTDI FT220X chip.

PROGLOG01

PROGLOG01

Small low-power open-source toolchain compatible FPGA

USB232R01B

USB232R01B

The module is universal converter from USB to RS232 with TTL/CMOS signal levels (both 3.3V and 5V). The converter uses FT232R chip from FTDI and is supported in all main operating systems.

USB232R01

USB232R01

The module is universal converter from USB to RS232 with TTL/CMOS signal levels (both 3.3V and 5V). The converter uses FT232R chip from FTDI and is supported in all main operating systems.

RS232SINGLE01A

RS232SINGLE01A

The module uses well known MAX232 chip and is intended as a level converter. It uses RX/TX signals and a pair of flow control signals (selectable by jumpers). Original RS232 signals are available on header pins.

I2CHUB02

I2CHUB02

I2CHUB02 is low voltage I2C multiplexer (hub) which allows you to divide I2C bus into 8 separate buses, where the user can switch and connect individual sub-bus differently. This can connect multiple I2Cs to the device, change the voltage levels, or disconnect a certain part of the bus when it is stuck.

USBI2C01

USBI2C01

USB device to I²C master adapter with Linux kernel support

I2CPWM01A

I2CPWM01A

The module allows the generation of PWM signal, which can be adjusted using the I2C interface. The module has eight outputs that can run simultaneously on two frequencies in the range of 0.59 Hz - 152 Hz (with 1.69 - 6.58 ms).

USB232R02

USB232R02

Universal USB-UART converter ideal for prototyping high-quality devices. USB Full Speed/Full Handshake support.

TTLRS48501A

TTLRS48501A

The module allow conecting uprocesors to RS485 bus

ADCmonoSPI01B

ADCmonoSPI01B

Mono high resolution (16bit) analog to digital converter. With serial data output.

EEPROM02A

EEPROM02A

Universal EEPROM module for communicating via the I2C interface in package types: SO8, TSSOP8, MSOP8.

ALBASE1521

ALBASE1521

MLAB base-board with size 15x21 holes with standard MLAB grid 400mils (10.16mm). The board on the sides contains a series of M3 holes with a metric pitch (10 mm) and three holes for stacking the boards above each other.

ALBASE1609

ALBASE1609

MLAB aluminium baseboard with 16x9 holes with a standard pitch of 400mils (10.16mm). Suitable for devices placed in the 1455N1601 box.

WINDGAUGE02B

WINDGAUGE02B

Anemometer with RTC03A counter

BASE162101A

BASE162101A

MLAB base for modules constructions.

ALBASE1208

ALBASE1208

This base board has size 12x08 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions.

ALBASE1115

ALBASE1115

This base board has size 11x15 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions.

ALBASE0401

ALBASE0401

This base board has size 4x1 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions.

PLBASE1515

PLBASE1515

This base board has size 15x15 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions. The board can be prited at almost any 3D printer.

ALBASE1608

ALBASE1608

This base board has size 16x08 holes and standard MLAB grid 400mils (10.16mm)

UNIBOX01A

UNIBOX01A

Universal metal module housing box with interchangeable front and back panels. Useful for housing construction of devices created from MLAB modules.

ALBASE1521B

ALBASE1521B

MLAB base-board with size 15x21 holes with standard MLAB grid 400mils (10.16mm)

ALBASE1241

ALBASE1241

This base board has size 12x41 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions.

ALBASE1505

ALBASE1505

Motherboard ALBASE1505 has 15x5 holes with a spacing of 10.16 mm. Its overall dimensions are adapted for insertion into the box UNIBOX03A.

ALBASE1209

ALBASE1209

This base board has size 12x09 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions.

ALBASE2537

ALBASE2537

This base board has size 25x37 holes and standard MLAB grid 400mils (10.16mm). It is especially suited for simple measuring instruments and mobile robots constructions.

DRV8835HB01B

DRV8835HB01B

H-bridge-based ICs DRV8835HB. Allows you to control two DC motors in the range voltage 2V to 11V and maximum current of 1.5 A on the engine, or parallel, where it is then possible to control the 3A engine. Or the module can be used to control a stepper motor.

VLFANT01

VLFANT01

VLF antenna connection module

ISM01

ISM01

Universal sub GHz ISM band transceiver MCU.

QFHBAL01

QFHBAL01

Balun for QFH mix antennas

ISM02

ISM02

ISM RF module with LoRa network capability

SDRX01

SDRX01

Direct conversion IQ output SDR receiver.

BP02

BP02

Symmetrical RF filter module with SATA connector input/output

SATABAL01

SATABAL01

RF balun with unballanced MCX/SMA and balanced SATA connectors

SHT25V01

SHT25V01

None

LIGHTNING01

LIGHTNING01

Lightning sensor module based on AS3935 Franklin Lightning Sensor IO. Sensor can be connected via I2C or SPI bus.

DATALOGGER01

DATALOGGER01

Universal Arduino based data logger to SDcard.

PCRD01

PCRD01

Semiconcductor cosmic radiation detector Silicon diode interface.

PCRD06

PCRD06

Sample and hold circuit for photomultiplier pulse signal processig

GPS02

GPS02

GPS02B is GNSS reciever with support of RTK (Real time kinematics) technology. GPS02B reciever is based on u-blox NEO-M8P reciever.

RGBFEE01

RGBFEE01

None

R1S01

R1S01

None

VCAI2C02

VCAI2C02

High power voltage and current measuring ADC with I2C interface

HCS01

HCS01

None

HUM01

HUM01

Humidity sensor based on HIH-5030/5031 chip. Analog output is ratiometric.

IMU01

IMU01

None

PCRD04

PCRD04

Silicon PIN diode cosmic radiation detector

SHT31V01

SHT31V01

None

ISL02

ISL02

None

IUC01

IUC01

None

GSENSE01

GSENSE01

None

IRFEE01

IRFEE01

None

RGBC01

RGBC01

None

PCRD03

PCRD03

Silicon PIN diode cosmic radiation detector

VCAI2C01

VCAI2C01

voltage and current measuring ADC with I2C interface

MAG01

MAG01

None

RPS01

RPS01

None

ISL03

ISL03

Light sensor with I2C interface to 168 klx.

GPS01

GPS01

uBlox LEA-6 GNSS receiver module

PCRD05

PCRD05

Silicon photomiltiplier radiation detector

PCRD02

PCRD02

Silicon PIN diode cosmic radiation detector

ALTIMET01

ALTIMET01

Precision barometric sensor. Board is designed for MPL115A1 or MPL115A2 integrated sensor chips.

PIND01

PIND01

None

LTS01

LTS01

None

FIELDMILL01

FIELDMILL01

Electric field mill sensor

SOLARMINI01

SOLARMINI01

Small low-power MPPT module for photovoltaic cells.

SUPERCAP01B

SUPERCAP01B

The module is suitable for covering power outages devices. By detecting the input voltage drop can be used for early shutdown of computers type ODROID on power.

BATPOWER04

BATPOWER04

High-effeciency (over 90%) stepdown converter based on LM3485 PFET Buck controller. Input vortage 4.5 V - 16V; Output voltage can be selected by jumper in fixed values of 3,3V, 5V or custom voltage by external resistor or trimmer.

UNIPOWER02

UNIPOWER02

Universal power supply module from barrel DC connector and WAGO terminals to MLAB modules. The module contains a resettable fuse, switch and LED indicator. Module can be used either for 5V and 12V.

STEPUPDC02

STEPUPDC02

Step-up converter. Vin 1,8 V - 5 V, Vout up to 28 V.

VLT01

VLT01

None

AT32TQ14401A
avr

AT32TQ14401A

Module is intended for development of applications based on powerful 32bit Atmel microcontrolers with AVR32 core AT32UC3A series.

ATmegaTQ4401A
avr

ATmegaTQ4401A

Processor module for ATMEL ATmega in TQFP44 package. The module can use standard and/or clock crystals. It is equipped with RESET push button and programming connector for ISP (6 PIN) and JTAG (10 PIN) programming.

ATmegaTQ6401A
avr

ATmegaTQ6401A

Processor module for ATMEL ATmega in TQFP64 package. The module can use standard and/or clock crystals. It is equipped with RESET push button and programming connector for ISP (6PIN) and JTAG (10PIN) programming.

ODROID-C1
ARM

ODROID-C1

Computer module for applications which needs full Linux operating system and lot of computing power. It is suitable for machine control or home automation as example.

ODROID-C2
ARM

ODROID-C2

Computer module for applications which needs full Linux operating system and lot of computing power. It is suitable for machine control or home automation as example.

RPi3
ARM

RPi3

Documents and design files describing a mothod how to use classic Raspberry Pi 3 in MLAB prototyping system.

RTC03A

RTC03A

Modul contains real-time clock IO PCF8583, which can work as signal counter up to 20kHz.

CLKGEN02A

CLKGEN02A

The module comprises a plurality of housings for mounting a variety of crystal oscillators.

TRIACSHARP02A

TRIACSHARP02A

There are 8 solid state switching relays which can be digitally controlled by open collector. It can operate up to 8A on 250VAC.

NFET4X01B

NFET4X01B

There are 4 NFETs switching to GND. Parameters depending on type of soldered FETs. Inductive load is allowed.